{"id":6827,"date":"2026-11-02T09:07:58","date_gmt":"2026-11-02T01:07:58","guid":{"rendered":"https:\/\/sdftools.com\/solid-carbide-drills-aluminum-extrusions-entry-burrs-exit-breakout-hole-position\/"},"modified":"2026-11-02T09:07:58","modified_gmt":"2026-11-02T01:07:58","slug":"solid-carbide-drills-aluminum-extrusions-entry-burrs-exit-breakout-hole-position","status":"publish","type":"post","link":"https:\/\/sdftools.com\/de\/solid-carbide-drills-aluminum-extrusions-entry-burrs-exit-breakout-hole-position\/","title":{"rendered":"Solid Carbide Drills for Aluminum Extrusions: How to Control Entry Burrs, Exit Breakout and Hole Position"},"content":{"rendered":"<p>Drilling holes in an aluminum extrusion can become unstable when the drill enters a curved or thin wall, breaks through into a hollow section, and leaves a burr that interferes with assembly. The material may cut freely, but the component geometry creates its own problems: variable wall thickness, unsupported exit areas, long parts that can vibrate, and chips that scratch finished surfaces. A solid carbide drill can provide a controlled route to hole quality when the entry, tool geometry, coolant method, and workholding are planned together.<\/p>\n<h2>Why aluminum extrusions challenge a simple drilling cycle<\/h2>\n<p>An extrusion is not always a flat, fully supported block. A hole may begin on a narrow land, pass through a web, emerge into an internal cavity, or exit close to an outside edge. Each transition changes the axial support under the drill. If the work moves at entry or the drill breaks through into an unsupported wall, the hole can show location shift, deformation, breakout, or a heavy burr.<\/p>\n<p>First, review the section drawing and identify every material transition along the hole axis. Confirm the local wall thickness, entry angle, nearest edge, hole tolerance, and whether the hole will receive a fastener, thread, seal, or locating feature. This avoids treating a structural extrusion like a uniform billet.<\/p>\n<h2>Prepare a stable entry surface and workholding plan<\/h2>\n<p>The drill should enter a surface that is perpendicular and well supported whenever the drawing permits. A curved, angled, rough-sawn, or narrow starting land can deflect the point before the margins have established guidance. Mill a local pad or use an appropriate spotting operation when needed, while respecting the finished-part requirements. The related guide to <a href=\"https:\/\/sdftools.com\/de\/solid-carbide-drills-inclined-surfaces-position-hole-quality\/\">drilling on inclined surfaces<\/a> explains why a controlled entry is important for hole location.<\/p>\n<h3>Support the part close to the hole<\/h3>\n<p>Clamp long profiles without crushing thin walls, and place support near the drilling area where possible. A fixture that holds only the ends of a long extrusion can permit vibration at the cutting point. Support also matters at breakthrough: if the exit wall is free to flex, it can tear or leave a larger burr than the same hole in a supported section.<\/p>\n<h2>Select drill geometry for aluminum chips and the required depth<\/h2>\n<p>Aluminum chips can become long and may adhere to a cutting edge when the geometry, lubrication, or cutting data are unsuitable. A solid carbide drill for this work should be evaluated for flute capacity, edge preparation, point design, coating or uncoated surface, and the planned depth-to-diameter ratio. The best choice is determined by the exact alloy, the hole depth, coolant availability, and whether the drill must pass through changing wall sections.<\/p>\n<p>For stable operations where through-tool coolant is available, the <a href=\"https:\/\/sdftools.com\/de\/product\/sdf-p-series-general-high-performance-internal-cooling-solid-carbide-drill-with-dh-coating\/\">SDF P Series internal-coolant solid carbide drill<\/a> is a standard tool family to assess against the drawing and machine capability. Internal coolant can help move chips through the flute path, but it is effective only when coolant cleanliness, pressure, holder sealing, and machine delivery are appropriate.<\/p>\n<h2>Control chip evacuation without overusing pecking<\/h2>\n<p>Chip evacuation is a process decision, not an automatic reason to use a long peck cycle. A well-supported, moderate-depth hole with suitable flute space may run in one controlled feed. If chips are stringing, packing, or scratching a finished surface, use a chip-break or retract strategy that clears the flute without repeatedly re-entering against loose chips. Excessive pecking can add cycle time, mark the hole, and create a less stable breakthrough.<\/p>\n<h3>Use coolant or air to clear the work zone<\/h3>\n<p>Through-tool coolant, external coolant, air, or a compatible mist method can be selected according to the machine and component-cleanliness requirement. Direct the flow to carry chips away from the drill and the profile surface. If the workpiece must remain cosmetically clean, confirm that the chosen fluid and chip-removal method do not leave residue or recirculate chips into adjacent features.<\/p>\n<h2>Protect hole location through material transitions<\/h2>\n<p>When a drill moves from one wall into an internal void and then into a second wall, the load changes suddenly. Use the shortest practical projection, a clean holder, and checked runout so that the drill has the best chance to remain on location. Avoid forcing a drill through an unsupported exit merely by increasing feed. Instead, validate the complete cycle on representative section geometry and inspect both entry and exit results.<\/p>\n<p>For drills close to an external wall or edge, material support becomes even more important. See the article on <a href=\"https:\/\/sdftools.com\/de\/solid-carbide-drills-near-edge-holes-steel-breakout-entry-burrs\/\">near-edge drilling<\/a> for a related discussion of breakout and entry stability. The material differs, but the principle is the same: the local feature geometry can govern the result as much as the drill grade.<\/p>\n<h2>Plan for burr control at breakthrough<\/h2>\n<p>Exit burrs are often an assembly and appearance issue in aluminum profiles. Before changing the drill, identify whether the burr is caused by unsupported material, a worn cutting edge, a poor exit condition, runout, chip packing, or unsuitable cutting data. A secondary deburring or chamfering step may be the most controlled choice for a critical cosmetic or sealing edge; it should be specified and measured rather than assumed to disappear during drilling.<\/p>\n<h3>Inspect both sides of the profile<\/h3>\n<p>Measure the hole from the datums that matter to the assembly. Check location, diameter, roundness where required, entry burr, exit burr, and the condition of any internal wall. A hole can meet a diameter check while still having an exit breakout or burr that prevents a fastener from seating. For broad aluminum holemaking principles, review <a href=\"https:\/\/sdftools.com\/de\/solid-carbide-drills-aluminum-chips-heat-hole-quality\/\">SDF\u2019s guide to solid carbide drills for aluminum<\/a>.<\/p>\n<h2>Set cutting data from evidence, not a generic number<\/h2>\n<p>Start with the drill recommendation for the material and diameter, then make changes based on chips, spindle load, hole quality, and tool wear. Feed that is too low can encourage rubbing and built-up edge; feed that is too high for the support condition can deform the exit wall or reduce location control. Inspect the cutting edges and margins at planned intervals. A sudden burr change can be a useful early signal that the edge or fixture condition has changed.<\/p>\n<p>Keep a short process record for the profile: alloy or temper when known, section geometry, drill diameter and projection, holder, coolant method, cutting data, clamping arrangement, and measured results. This gives a repeatable baseline when the extrusion batch or component design changes.<\/p>\n<h2>How SDF standard and custom tools fit extrusion drilling<\/h2>\n<p>The <a href=\"https:\/\/sdftools.com\/de\/product-category\/drilling-tools-z\/\">SDF solid carbide drill range<\/a> includes standard external- and internal-coolant options for CNC holemaking. Standard drills are a practical first choice when the diameter, depth, and access fit the application. If an extrusion requires a special point, controlled chamfer, step, restricted reach, or combined drilling and finishing feature, SDF can review the drawing and recommend a standard or application-specific carbide tool approach.<\/p>\n<p>For an informed tooling review, provide the extrusion cross-section, alloy and temper if available, hole drawing and tolerance, entry and exit conditions, fixture concept, machine and holder, coolant method, current cutting data, and photos of the burr or breakout. <a href=\"https:\/\/sdftools.com\/de\/contacts\/\">Contact SDF Tools<\/a> to discuss the next step.<\/p>\n<h2>FAQ<\/h2>\n<h3>Why does an aluminum extrusion hole have a large exit burr?<\/h3>\n<p>Common causes include an unsupported exit wall, a worn edge, drill runout, unsuitable cutting data, or chips at the point of breakthrough. Inspect the local section geometry before changing the tool alone.<\/p>\n<h3>Is internal coolant necessary for aluminum extrusion drilling?<\/h3>\n<p>Not always. The choice depends on hole depth, diameter, chip behaviour, machine coolant capability, and the part\u2019s cleanliness requirements. Evaluate the full system.<\/p>\n<h3>Should every hole in an extrusion be spot drilled?<\/h3>\n<p>No. A stable, perpendicular, supported entry may not require a separate operation. Use spotting or surface preparation when the actual entry condition needs more guidance.<\/p>\n<h3>What details help with a custom drill request?<\/h3>\n<p>Send the section and hole drawings, aluminum grade or temper, hole depth and tolerance, local wall thickness, fixture and coolant details, current parameters, and evidence of the process problem.<\/p>","protected":false},"excerpt":{"rendered":"<p>Drilling holes in an aluminum extrusion can become unstable when the drill enters a curved or thin wall, breaks through [&hellip;]<\/p>\n","protected":false},"author":0,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[65],"tags":[],"class_list":["post-6827","post","type-post","status-publish","format-standard","hentry","category-cnc-cutting-tool-news"],"_links":{"self":[{"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/posts\/6827","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/types\/post"}],"replies":[{"embeddable":true,"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/comments?post=6827"}],"version-history":[{"count":0,"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/posts\/6827\/revisions"}],"wp:attachment":[{"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/media?parent=6827"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/categories?post=6827"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/sdftools.com\/de\/wp-json\/wp\/v2\/tags?post=6827"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}