Fábrica de herramientas de fresado y corte sdftools

Internal Coolant Carbide Drills for Deep Blind Holes in P20 Mold Steel: How to Control Chips, Bottom Quality and Tool Load

A deep blind hole in P20 mold steel can look routine on a drawing, yet become expensive when chips pack near the bottom, the drill begins rubbing, or the finished floor varies from cavity to cavity. The problem is not solved by simply reducing feed. For internal coolant carbide drills, reliable blind-hole drilling comes from matching drill geometry, usable length, coolant delivery and the cycle to the actual hole depth and machine stability.

This guide explains how to use internal coolant carbide drills for deep blind holes in P20 mold steel with a process-led approach. It applies to mold plates, inserts and other pre-hardened steel parts where repeatable hole location and clean bottom conditions matter as much as cycle time.

Why deep blind holes in P20 create a chip-management problem

P20 is commonly selected for mold work because it offers a practical balance of machinability, polishability and strength. In a blind hole, however, the drill cannot push chips out through the exit. The flutes must carry each chip back through an increasingly long contact zone, while coolant has to reach the cutting edges and help move heat and chips in the same direction.

Chip packing changes the cutting conditions quickly

When chips recut at the bottom of a hole, torque rises and the margin can start to rub. That raises heat, dulls the cutting edges and may leave scoring on the wall. A tool that cuts acceptably for the first holes can then become unstable with little warning. The response should be to inspect chip form, coolant flow and flute clearance before making a large feed reduction.

Bottom geometry needs allowance in the program

Most twist drills produce a conical point at the bottom. If a drawing calls for a usable cylindrical depth, program the drill depth with the point geometry in mind and leave the required allowance for a later flat-bottom operation when necessary. Driving the drill deeper only to chase a flat condition can overload the margins and make chip evacuation less reliable.

Choose the drill around depth, rigidity and coolant access

The first selection question is not only diameter. Confirm the hole depth-to-diameter ratio, the available machine spindle pressure, holder runout and whether the fixture exposes the drill to vibration. A shorter, more rigid drill is usually the safer choice when it can reach the required depth.

Use internal coolant when chip transport is the limiting factor

Internal coolant carbide drills direct fluid to the cutting zone, helping cool the lips and carry chips through the flutes. The benefit depends on adequate pressure and clean coolant. Low flow, blocked filtration or poor spindle-to-tool sealing can remove the advantage of an internal-coolant design. Verify the actual flow path during setup instead of assuming the machine setting reaches the cutting edge.

Match flute capacity to the actual drilling cycle

A deep blind-hole cycle needs room for chips as well as cutting edges. Select a drill family intended for the material and depth range, then use a peck or chip-break strategy only when the application truly needs it. Excessive retracting can rub the wall, waste time and disturb a stable chip. Conversely, a continuous feed without sufficient chip space can overload the drill near the bottom.

For available product options, review SDF’s internal-coolant deep-hole drills for steel and cast iron alongside the wider solid carbide cutting-tool range. The final choice should be based on the part material, depth, coolant capability and required tolerance.

Build a stable entry before the drill reaches depth

Deep-hole results often start at the first millimeters. An angled, interrupted or poorly supported entry can force the drill off center before the margins establish guidance. That initial deviation becomes harder to correct as the drill advances.

Prepare the starting surface

Whenever possible, present the drill with a flat, clean surface normal to the intended hole axis. If the feature begins on an incline or curved surface, use an appropriate spotting or interpolation operation to create support. Keep the setup free of scale, burrs and loose material that could deflect the point.

Control holder runout and tool projection

Runout can make one cutting lip carry more load than the other. The result may be oversize holes, asymmetric wear and reduced tool life. Check the holder, collet or hydraulic chuck close to the cutting end and use only the projection needed for clearance. The same principle applies to the workholding: unsupported mold plates can vibrate even when the spindle and drill are sound.

Set cutting data from observed chip behavior

Published starting data is useful, but it is not a substitute for observing the actual chip, sound and spindle load. P20 hardness, heat treatment condition, coolant concentration and machine stiffness all influence the final window. Begin conservatively within the drill supplier’s recommended range and adjust one variable at a time.

Feed too low can create rubbing

Reducing feed may seem protective, but a feed that is too low can produce thin chips and encourage rubbing. The heat then concentrates at the edge and margin. If the drill is rubbing, confirm runout, coolant and chip evacuation before assuming the answer is a still lower feed.

Use pecking as a controlled intervention

Pecking is valuable when it breaks chips or refreshes evacuation in a difficult depth range. Use shallow, purposeful cycles rather than arbitrary full retracts. Watch the chips and wall condition after a small test quantity. A stable process is usually easier to maintain with the simplest cycle that clears chips reliably.

Inspect the hole and the drill as one system

Hole diameter, location, straightness and bottom condition are process signals. Measure a representative sample at entry and depth, and compare the results with the drill’s wear pattern. Built-up edge, chipped corners, polished margins and discoloration point to different causes. Do not replace a drill repeatedly without learning why the previous one changed.

Track wear before it becomes a breakage event

For repeat work, define a practical inspection interval and tool-change criterion. A controlled tool change is less disruptive than waiting for a margin failure or a broken drill inside a valuable mold component. Record material batch, hole depth, coolant condition and any cycle changes so the next setup starts from evidence.

Where SDF standard and custom tooling fit

SDF supports standard solid carbide drill families for common steel drilling requirements and can review special cases where the hole, reach, coolant path or downstream operation makes a standard selection unsuitable. Compare the application with SDF’s guide to 3×D versus 5×D solid carbide drills for steel and its article on drilling P20 mold steel before locking the process.

If a drawing has unusual depths, stepped features or a specific inspection target, send the part details through the custom tooling request page. For general product and application questions, the SDF contact page is the right starting point.

FAQ: Internal coolant carbide drills for deep blind holes

Do internal coolant drills eliminate the need for pecking?

No. Internal coolant improves cooling and chip transport, but the required cycle still depends on diameter, depth, material, chip form and machine capability. Use the simplest cycle that keeps chips moving.

Why is the hole oversize near the entrance?

Common causes include holder runout, an unstable entry surface, worn margins or insufficient clamping. Check those items before changing the drill diameter or compensation.

Can one drill make a finished flat-bottom blind hole?

A standard drill leaves a point form. When the print requires a true flat floor, plan a separate finishing operation or specify a tool designed for the required bottom geometry.

Conclusion

Successful deep blind-hole drilling in P20 depends on chip movement, not just cutting speed. Start with a rigid entry, an internal-coolant drill suited to the depth, verified coolant delivery and a cycle shaped by real chip behavior. That approach protects the hole, the tool and the value already built into the mold component.

share this recipe:
Facebook
Twitter
Pinterest

Still hungry? Here’s more

Scroll al inicio

Get a fast response from our expert